Technischen Daten

PHYSIKALISCH-MECHANISCH-ELEKTRISCHE HAUPTEIGENSCHAFTEN

EIGENSCHAFTEN
PRÜFMETHODE
MENGENEINHEIT
POLYESTER-MATTE
POLYESTER-MATTE
selbstverlöschend
ACRYL MATTE
selbstverlöschend
Mechanische Haupteigenschaften
Zugfestigkeit Längsgerichtet ASTM D638 MPa 400 400 300
Elastizitätsmodul Längsgerichtet ASTM D638 GPa 26 26 22
Zugfestigkeit Quergerichtet ASTM D638 MPa 30 30 20
Elastizitätsmodul Quergerichtet ASTM D638 GPa 8 8 7
Biegefestigkeit Längsgerichtet AST MD790 MPa 400 400 300
Biegemodul Längsgerichtet EN 13706 GPa 25 25 21
Biegefestigkeit Quergerichtet ASTM D790 MPa 70 70 60
Biegemodul Quergerichtet ASTM D790 GPa 7 7 6
Druckfestigkeit Längsgerichtet ASTM D695 MPa 250 250 160
Kompressionsmodul Längsgerichtet ASTM D695 GPa 18 18 15
Druckfestigkeit Quergerichtet ASTM D695 MPa 70 70 55
Kompressionsmodul Quergerichtet ASTM D695 GPa 7 7 6
Scherfestigkeit Längsgerichtet ASTM D2344 MPa 30 30 20
Schubmodul Längsgerichtet ISO 179 GPa 3 3 2,4
Schlagzähigkeit (CHARPY) ASTM D5942 kJ/m2 170 170 140
Schiebefestigkeit Längsgerichtet ASTM D953 MPa 170 170 130
Schiebefestigkeit Quergerichtet ASTM D953 MPa 70 70 50
Poisson-Verhältnis Längsgerichtet ASTM D3039 0,28 0,28 —-
Poisson-Verhältnis Quergerichtet ASTM D3039 0,12 0,12 —-
Physikalisch Haupteigenschaften
Barcol-Härte ASTM D2583 °B 45 45 50
Dichte ASTM D792 g/cm3 1,8 1,8 2
Glasanteil (Gewichtsprozent) ISO 1172 % 58 58 48
Wasseraufnahme ISO 62 % 0,4 0,4 05
Wärmeausdehnungskoeffizient ISO 11359-2 K-1 11X10-6 11X10-6 9×10-6  
Wärmeleitfähigkeit EN 12667
EN 12664
W/mK 0,3 0,3 0,35
Toxizitätsindex CEI 2037
part 2
/ —-  <2  <1
Elektrische Haupteigenschaften
Durchschlagsfestigkeit ASTM D149 kV/mm 5 5 10
Dielektrizitätskonstante 50 Hz ASTM D150 5 5 5
Verlustfaktor 50 Hz (Tg Δ) ASTM D150 0,5 0,5 0,5
Oberflächenwiderstand EN 61340 1012 1012 1012
Elektrischer Widerstand EN 60112 V —- —- CTI 600
ALLE WERTE BEZIEHEN SICH AUF GLASFASER-PROFILE MIT VERSTÄRKUNGSFASERN AUS POLYESTER-ACRYL-MATTE
Kennwerttoleranz der mechanischen Eigenschaften in Längsrichtung: ± 10 %.
Die angegebenen Werte sind zuverlässig, dennoch übernimmt Top Glass keine Haftung für deren Verwendung.
EIGENSCHAFTEN
PRÜFMETHODE
MENGENEINHEIT
POLYESTER-MATTE
POLYESTER-MATTE
selbstverlöschend
ACRYL MATTE
selbstverlöschend
FEUERBESTÄNDIGKEITSKLASSE “M” NF F 16-101 Klass —- M3/M2 M1
FEUERBESTÄNDIGKEITSKLASSE “F” NF P 92-501 Klass —- F2 F0
Flammenausbreitung BS 476 part 7 Klass —- 3 1
Optische Rauchdichte BS 6853 Indice —- —- A0 (On) = 9
A0 (Off) = 10
Flammenausbreitung und Entwicklung von giftigen Rauchen ASTM E84 Klass —- / 1
Flammpunkt(Glühdrahtprüfung) IEC 695-2-1 °C —- / 960
(senza sgocciolamento)
Halogen-Präsenz / / Nein Ja Nein
Entflammbarkeit (Horizontale Probe) UL 94 Grad HB / V0
Toxizitätsindex CEI 2037 part 2 / —- <2 <1>
Entflammbarkeit (Vertikale Probe) UL 94 Grad —- V1/V0 V0
ALLE WERTE BEZIEHEN SICH AUF GLASFASER-PROFILE MIT VERSTÄRKUNGSFASERN AUS POLYESTER-ACRYL-MATTE
Kennwerttoleranz der mechanischen Eigenschaften in Längsrichtung: ± 10 %.
Die angegebenen Werte sind zuverlässig, dennoch übernimmt Top Glass keine Haftung für deren Verwendung.

DIMENSIONAL TOLERANCES

The ASTM D3917 specification defines tolerances applicable to pultruded profiles with traditional geometric shapes as: C, H, Angles, Hollow profiles, Rods, etc. based on thermosetting resins. Custom shapes based on customer design can have different tolerances and must be agreed in the supply contract phase.

SHAPE AND THICKNESS DIMENSIONAL TOLERANCES

A = ± 4% of specified dimension (but not more than 2.39 mm) (see note)

B (wall thickness -open shape) = ± 10% of specified dimension but not exceeding either ± 0.25 mm(see note)

B (flat profiles width from 304.8 till 1981.2 mm) = ± 15% of specified dimension to 3.175 mm thickness but not exceeding ± 0.25 mm min

B (Flat Sheets width from 304.8 till 1981.2 mm) = ± 10% of specified dimension up 3.175 mm thickness but not exceeding ± 1.27 mm max

C (wall thickness - close shape) = ± 20% of specified dimension but not exceeding 0.25 mm min (see note)

Note: APPLICABLE TO SHAPES THAT CAN BE INSCRIBED IN A 914.4 mm MAX DIAMETER CIRCLE

STRAIGHTNESS

Rods and square, hexagonal, and octagonal bars – all dimensions:
D = 2.5 mm/m, measured without taking into account the profile weight
Rectangular bars up to 38.07 mm width and to 2.38 mm thickness, included:
D = 4.17 mm/m, measured without taking into account the profile weight
Rectangular bars up to 38.07 mm width and over 2.38 mm thickness:
D = 3.33 mm/m, measured without taking into account the profile weight
Rectangular bars over 38.07 mm width and all thicknesses:
D = 3.33 mm/m, measured without taking into account the profile weight
Open shapes, all dimensions:
D = 4.17 mm/m, measured without taking into account the profile weight
Closed shapes, all dimensions:
D = 2.5 mm/m,
Flat SheetD = 2.5 mm/m,

Measured when weight of pultrusion minimizes the deviation by contact with flat surface

TWIST

LENGTHS OVER 6 m ARE NOT CONSIDERED IN THIS STANDARD
BARS and OPEN SHAPES :
All dimensions and thickness: permitted Y = 3.28°/m twist up to 6. m in length
CLOSED SHAPES:
All dimensions and thicknesses : permitted Y = 3.28°/m twist up to 6 m in length, but not more than 7° total
THE MEASUREMENT MUST BE DONE KEEPING ONE SIDE OF THE PROFILE WELL FIXED ON A FLAT SURFACE AND MEASURING THE ANGLE DEVIATION ON THE OPPOSITE SIDE WHEN THE PROFILE WEIGHT MINIMIZES THE TWIST.

FLATNESS (FLAT SURFACES)

STANDARD BARS, SOLID SHAPES, SEMIHOLLOW SHAPES, AND FLAT SHEET
Width till 25.4 mm
PERMITTED A VERTICAL DEVIATION OF 0.2 mm x W (mm)
Width up to 25.4 mm
PERMITTED A VERTICAL DEVIATION OF 0.008 mm x W (mm) FOR ALL DIMENSIONS IN TERMS OF THICKNESS
IF "W" = 120 mm, THE VERTICAL DEVIATION "D" IS: 0.008 x120 = 0.96 mm
FLAT SHEETS
PERMITTED A VERTICAL DEVIATION OF 0.008 mm x W (mm) 6.35 mm max.

FOR ALL DIMENSIONS IN TERMS THICKNESS

ANGULARITY

Leg thickness up to 19.02 mm included ± 2° THE STANDARD DOES NOT APPLY TO THICKNESS OVER 19.02 mm

SQUARENESS OF END CUT

Profiles over 50.8 mm in diameter or width: ± 1°
Profiles 50. 8 mm inclusive and under in diameter or width: ± 2°